Pontiac 461ci Pro Street Crate Engine
Pontiac 400ci two bolt main block 100% CNC bored to 4.155 for 461ci up 4.185″ which is a 468ci engine if required for a perfect clean final bore, cnc square decked, internally balanced 4.250″ 4340 Steel Crank, 6.800 H Beam Rods with 7/16 8740 Rod Bolts, Carrillo or Mahle forged flat pop pistons. Pontiac race prepared steel heads with new moving components, valves, springs, retainers, locks, seals, valve guides and exhaust seats if required; Assembled, Dyno Tested and Tuned for pump gas
$10,195.00
http://www.youtube.com/watch?v=-z8-gGh8wkY
10.222″ Deck | 4.155-85″ Bore | 4.350″ Stroke | 6.800″ Rods | 650lb 4400 – 610Hp @5200
Components
- Pontiac 400-M 100% 4 Axis CNC Race Prepped to 4.155 to 4.185″ Bore Block
- ARP Head Bolt and Main Stud Kit
- Brass Freeze Plug Complete Block Kit
- Eagle 4.250″ Internally Balanced 4340 Steel Crank
- Eagle 6.800″ H Beam 4340 Steel Rods with ARP 7/16 Rod Bolts
- Clevite or King Race Series Main and Rod Bearings
- Carrillo or Mahle 10.75:1 Forged Flat Top Pistons
- Mahle or Total Seal File to Fit Plasma Moly Rings
- Competition Cams Magnum Hydraulic Roller Cam
- Comp Cams, Erson or Morel Hydraulic Roller Lifters
- Competition Cams Double Roller Timing Chain and Gear Kit
- New Aluminum Front Timing Cover Kit
- New Internally Balanced Damper
- Kauffman 310cc 85cc Aluminum D Port Exhaust Heads
- Ferrea Stainless Steel Valves
- PAC Racing 1.437 Springs, 10° Tool Steel Retainers
- Fel Pro Engine Gaskets and Viton 2 Piece Rear Main Seal
- Manley or Trend .120″ Thick Wall Chrome Moly Push Rods
- Competition Cams #1451-16 Roller Tip Rocker Arms
- Melling M54DS HP Oil Pump and Proper Pickup Tube
- Moroso #20500 Stroker 7qt. Race Oil Pan with Baffling
- Short or Tall Chrome Valve Covers
- Edelbrock Torker II Intake Manifold
- Holley or Edelbrock 850 cfm Carburetor Dyno Tuned
- HEI Distributor, MSD 8.5 mm Wires, NGK Plugs (see options)
- Actual Shipping Charges to Your Zip Code for Pick Up
OPTIONS
AwesomeEngines® 100% 4 Axis CNC Race Prepped MR1 Iron Race Block with Steel Billet Main Caps
+ $2800.00
AwesomeEngines® 100% 4 Axis CNC Race Prepped MR1A Aluminum Light Weight Race Block
+ $3975.00
578CI 4.400″ MR1 Bore Block, 4.75″ 4340 Stroker Crank and Block Cleared for Maximum Cubic Inch and Power
+ $1875.00
Competition Cams or Harland Sharp Roller Rockers
+ $ 300.00
Jesel or T&D Shaft Rocker System Installed
+ $1295.00
Kauffman or Edelbrock Performer D Port 340 cfm 100% CNC Ported Aluminum Heads
+ $1595.00
Kauffman High Port Oval Port Exhaust CNC Ported Aluminum Heads
+ $2195.00
Kauffman North Wind Match Ported Intake Manifold and Crossover
+ $ 400.00
SFI Damper Specific Honed to Crankshaft Snout
+ $ 300.00
Holley or QFT 950 CFM Carburetor with Jomar CNC Ported Heat Sink Spacer and Hardware
+ $ 600.00
MSD Pro Billet Ready to Run #8528 Distributor, MSD Coil, MSD 8.5 mm Wires Complete Kit Dyno Tested with Engine
+ $ 600.00